IC-(10%,20%,30%,50%)-SOL
ACRYLIC ANTI‑SLIP COATING FOR EXTERIOR SURFACES
IC-SOL is a one-component acrylic coating designed for outdoor concrete or asphalt surfaces requiring slip resistance. It provides a textured, anti-slip finish available in a variety of colors. This water-based product is low odor and fast-drying.
IC-SOL is a one-component acrylic coating designed for outdoor concrete or asphalt surfaces requiring slip resistance. It provides a textured, anti-slip finish available in a variety of colors. This water-based product is low odor and fast-drying.
Advantages
• Anti-slip finish for enhanced safety
• Easy to apply by roller or brush
• Fast drying with low odor
• Water-based and solvent-free
• Good abrasion and weather resistance
Technical Specifications
Recommended Use
Coverage may vary depending on surface porosity and texture.
Surface Preparation
The surface must be clean, dry, and free from dust, oil, grease, loose paint, or other contaminants. New concrete should cure for at least 28 days. Surface profile ICRI‑CSP 2–3 is recommended. On asphalt, ensure surface is dry, stable, and not degraded.
Application
• Stir well before use
• Apply between 10°C and 30°C (50°F–86°F)
• Avoid direct sun and rainy conditions
• Use a textured roller or brush
• 1 to 2 coats recommended
• Wait 4 to 6 hrs between coats (depending on conditions)
Drying Times (23°C / 73°F, 50% R.H.)
Restrictions
• Do not apply if relative humidity exceeds 85%
• Avoid water exposure during the first 24 hours
• Not intended for high-traffic vehicle areas
• Store in a frost-free environment
Maintenance
Clean tools with warm soapy water immediately after use. Clean coated surfaces regularly using mild detergents. Avoid abrasive cleaning products.
• Anti-slip finish for enhanced safety
• Easy to apply by roller or brush
• Fast drying with low odor
• Water-based and solvent-free
• Good abrasion and weather resistance
Technical Specifications
Parameter | Value |
Packaging | 3.78 L (1 gal), 18.9 L (5 gal) |
Available Colors | Grey, Red, Green, Yellow, Blue, Beige, White, Black |
Solids by Volume | ± 50% |
Solids by Weight | ± 63% |
Density | 1.30–1.35 |
VOC | < 50 g/L |
Viscosity | 6000–8000 cP |
pH | 8.5–9.5 |
Flash Point | N/A (water-based) |
Pot Life | N/A (single-component) |
Storage Life | 12 months (room temperature, frost-free) |
Surface | Thickness | Approx. Coverage |
Concrete or asphalt | 5–8 mils | ± 200 ft²/gal |
Surface Preparation
The surface must be clean, dry, and free from dust, oil, grease, loose paint, or other contaminants. New concrete should cure for at least 28 days. Surface profile ICRI‑CSP 2–3 is recommended. On asphalt, ensure surface is dry, stable, and not degraded.
Application
• Stir well before use
• Apply between 10°C and 30°C (50°F–86°F)
• Avoid direct sun and rainy conditions
• Use a textured roller or brush
• 1 to 2 coats recommended
• Wait 4 to 6 hrs between coats (depending on conditions)
Drying Times (23°C / 73°F, 50% R.H.)
Stage | Approx. Time |
Touch dry | 1 hour |
Recoatable | 4–6 hours |
Foot traffic | 24 hours |
Full cure | 3–5 days |
• Do not apply if relative humidity exceeds 85%
• Avoid water exposure during the first 24 hours
• Not intended for high-traffic vehicle areas
• Store in a frost-free environment
Maintenance
Clean tools with warm soapy water immediately after use. Clean coated surfaces regularly using mild detergents. Avoid abrasive cleaning products.